How Many Solar Panels Does It Take to Run Central AC?

Best Solar Deal in California
Talk to An Expert!

Contact us today to learn more about Qcells and your savings!

Table of Contents

Short answer: The average air-conditioned U.S. home used about 2,300 kWh a year on cooling in 2020, according to EIA survey data. In California-level sun, that takes about 4 solar panels (400W) to cover over a year. To run that same central AC live at midday, you need about 8 or 9 panels of output. A bigger unit in a hot climate can take 8 to 14. Your number depends on your unit’s tonnage, its SEER2 rating, how many hours it runs, and how sunny your roof is.

You asked a simple question, and most of the answers you will find online are a little too confident. You will see “a central AC needs 10 to 18 panels” over and over. That is not wrong for every house, but it hides the thing that matters most: what you mean by “run.” Do you want solar to pay for your AC’s electricity over the year, or do you want it to power the compressor right now, at noon, on a 100-degree day? Those are two different panel counts, and this guide gives you both, plus the formula so you can plug in your own unit.

The Quick Answer: Panels by AC Size and Efficiency

Start here. Each row shows how much electricity the unit uses over a year and how many panels it takes to cover that, using a California-level production ratio of 1.5 (a 400W panel makes about 600 kWh a year, a 450W panel about 675). The “SEER2” column is the efficiency rating on your unit’s label: higher means less electricity for the same cooling.

Central ACSEER2Runtime a year (assumed)Average running powerkWh a yearPanels at 400WPanels at 450W
2-ton (24,000 BTU)14600 hours (mild)1.7 kW1,02922
3-ton (36,000 BTU)14900 hours (typical)2.6 kW2,31444
3-ton (36,000 BTU)18900 hours (typical)2.0 kW1,80033
3-ton (36,000 BTU)141,800 hours (hot)2.6 kW4,62987
3-ton (36,000 BTU)181,800 hours (hot)2.0 kW3,60066
4-ton (48,000 BTU)141,800 hours (hot)3.4 kW6,1711110
4-ton (48,000 BTU)181,800 hours (hot)2.7 kW4,80088
5-ton (60,000 BTU)141,800 hours (hot)4.3 kW7,7141312

How to read this table honestly:

  • The runtime hours are planning assumptions, not measured data. The 900-hour row is the one we can sanity-check: a 3-ton, 14 SEER2 unit running 900 hours uses 2,314 kWh, which lines up with the EIA national average of about 2,300 kWh for air-conditioned homes.
  • The 14 SEER2 rows are close to the legal minimum for a new unit. Under federal rules, new split systems under 45,000 BTU must hit 13.4 SEER2 in the North and 14.3 in the Southeast and Southwest. An older unit may be less efficient than that.
  • These counts are for the AC alone. Your whole-house count is bigger, and our guide to how many solar panels you need shows how to build it from your bills.

Two Questions Hiding Inside “Run My AC”

This is the part most guides skip, and it explains why you see “4 panels” in one place and “14 panels” in another. Both can be right. They answer different questions.

The questionWhat it really asks3-ton, 14 SEER2 example (400W panels)Who needs this answer
Will solar pay for my AC’s electricity?Yearly kWh from panels equals yearly kWh the AC usesAbout 4 panels (900 runtime hours)Most grid-tied homes where exported power earns a fair credit
Can solar power my AC right now?Panel output at midday matches the compressor’s drawAbout 9 panels (3.2 kW of panels)Homes that want to use their own power as it is made, or that are planning a battery or backup

Why the gap? Your AC does not run all year, and it does not run all day. It cycles on and off, and a big share of its hours fall in a few hot months. Over a year, a few panels make enough energy to cover it. But if you want solar to supply the compressor live, your panels need to produce at least the unit’s running power at that moment. On a hot afternoon, panels also make less than their label says. We use a planning figure of 80% of nameplate, so 2.57 kW of running power calls for about 3.2 kW of panels.

Many guides list 3,500 watts or more for a 3-ton and then divide by panel watts. That is closer to an older, low-efficiency unit or a hot-afternoon peak than to the seasonal average of a newer one, and it mixes the two questions. It is better to know which one you are asking.

How to Calculate Your Own Number

You need four things, and the first two are printed on your outdoor unit.

Step 1: Find your tonnage and SEER2 rating

Look at the label on the outdoor condenser. Tonnage is often hidden in the model number as a number divisible by 6 (24 is a 2-ton, 36 is a 3-ton, 48 is a 4-ton, 60 is a 5-ton). One ton is 12,000 BTU an hour. Units sold since 2023 list SEER2 on the yellow EnergyGuide label. If yours lists SEER, use that number as a rough stand-in.

Step 2: Work out the running power

Running kW = BTU per hour ÷ SEER2 ÷ 1,000. A 3-ton at 14 SEER2 is 36,000 ÷ 14 ÷ 1,000 = 2.57 kW. This is a seasonal average, so on the hottest afternoon the unit draws more.

Step 3: Estimate your runtime hours

The best source is your own data. Two easy ways: check the runtime report in a smart thermostat app, or compare a peak summer bill with a mild spring bill and attribute the difference to cooling. Download your hourly data if your utility offers it. Our guide to normal daily kWh shows how.

Step 4: Turn kWh into panels

Panels = AC kWh a year ÷ production ratio ÷ panel watts, rounded up. The production ratio is how many kWh each watt of panel makes in a year in your area, and the table in the next section has planning values. To learn more about how much one panel makes, see how much one panel produces.

Worked example: 3-ton, 14 SEER2, CaliforniaMathResult
Running power36,000 ÷ 14 ÷ 1,0002.57 kW
Yearly AC electricity (900 hours)2.57 × 9002,314 kWh
Yearly panels at 400W (ratio 1.5)2,314 ÷ 1.5 ÷ 400 = 3.94 panels
Live-at-midday panels at 400W2.57 ÷ 0.8 = 3.2 kW, then 3,214 ÷ 400 = 8.049 panels (8 at 450W)

Same AC, Different Sun: Panels by State

The same air conditioner needs more panels in a cloudier or lower-production state, because each panel makes less power there. This table holds the AC’s yearly use at the national average of 2,300 kWh so you can see the effect of sunshine alone. These are planning ratios from our sizing guide, not guarantees for your roof.

StatePlanning production ratiokW of panels to cover 2,300 kWhPanels at 400WPanels at 450W
California1.51.5 kW44
Texas1.61.4 kW44
Florida1.351.7 kW54
Illinois1.21.9 kW55
Connecticut1.152.0 kW55

There is a catch. A home in Houston or Miami runs its AC much more than 2,300 kWh a year, while a home in Connecticut runs it less. EIA says 88% of U.S. homes use air conditioning, but the hours vary a lot by region. So use the state table to understand how sun changes the count, then use your own runtime hours in the formula for the real number.

What Moves Your Number Up or Down

The cheapest panel is the one you do not need. These are the levers that change your count most, in rough order of impact.

  • The efficiency of the unit. Going from 14 to 18 SEER2 cuts the electricity per cooling hour by about 22% (1 minus 14 ÷ 18). For the typical 3-ton above, that takes the yearly count from 4 panels to 3.
  • How many hours it runs. For a 3-ton at 14 SEER2, every 100 fewer runtime hours saves about 257 kWh a year, close to half a panel. Shading the west windows, sealing and insulating the attic, fixing leaky ducts, and changing filters all shorten runtime.
  • Variable-speed units. These ramp up and down instead of starting and stopping, so they often run below full power. That helps both the yearly count and the battery you might add.
  • Panel wattage. The same energy takes fewer, higher-wattage panels. See our guide to Qcells panel wattage, or read about fewer, higher-wattage panels on tight roofs.
  • Roof direction and shade. A west-facing roof can match your afternoon AC better than a south-facing one, even if it makes a bit less in total. Your installer’s design software models this.

If your AC is old or failing, plan around the replacement. Sizing solar for a unit you are about to retire leaves you with panels you do not need, and sizing for the old unit and replacing it later overshoots. Mention it to your installer up front.

After Sunset: Panels Alone Versus Panels Plus a Battery

Here is the timing problem, and it is why a battery shows up in so many AC conversations. Your panels peak around midday. Your AC often peaks in the late afternoon and evening, when the sun is lower, and many utilities charge their highest rates.

  • Panels alone work well for the daytime hours. Anything your AC uses after the panels fade comes from the grid.
  • Where export credits are low, as under California’s net billing, the power your panels send to the grid at noon is worth much less than the power you buy back at 7 p.m. That is the gap a battery closes. See NEM 3.0 and batteries in California.
  • A battery stores your midday surplus and releases it in the evening. The Qcells Q.HOME CORE is modular, from roughly 10 kWh to just over 20 kWh of usable capacity, with round-trip efficiency around 90%. See our Qcells battery storage guide for the specs.

Here is how long a battery can run a central AC, using the running power from Step 2:

Usable battery capacity3-ton, 14 SEER2 (2.6 kW)3-ton, 18 SEER2 (2.0 kW)
10 kWhAbout 3.9 hours5.0 hours
20 kWhAbout 7.8 hours10.0 hours
8 hours of AC neededAbout 20.6 kWh16.0 kWh

Treat these as best-case. They ignore the rest of your house, and they assume the AC runs steadily, while real AC cycles and evenings cool off. Also remember the energy has to be made first. About a tenth is lost in the round trip, so charging the battery for a long evening of AC adds panels to your count.

One more thing that trips people up is the start-up surge. A compressor briefly pulls several times its running power when it kicks on. A battery or inverter can have enough capacity but too little peak power to start your air conditioner. Ask your installer for the surge rating, not just the kWh. Our solar inverter guide explains how that works. If outage backup is your main goal, see how a battery runs your home during an outage.

Adding an EV or a Pool Too? Add the kWh First

AC is rarely the only big load. If you are planning an EV, a heated pool, or a hot tub, add the yearly kWh together first and divide once at the end. Rounding each one up separately can leave you with a panel or two you do not need. These figures come from our sizing guide at a California ratio and 400W panels:

LoadTypical yearly kWhPanels at 400W on their own
Central air conditioningAbout 2,3004
Electric vehicle (average driving)About 3,0005
Heated swimming poolAbout 2,5005
Outdoor hot tubAbout 3,3006

Take a home with central AC, an EV, and a heated pool. Added separately, that is 4 + 5 + 5 = 14 panels. Added the right way, 2,300 + 3,000 + 2,500 = 7,800 kWh, divided by 600 kWh per panel, is 13 panels. Your real numbers will differ, so start with your own bills. For a full count, use the sizing guide, and if cost is the question, see how to read a solar quote.

The same formula works for a mini-split. A 1-ton (12,000 BTU) unit at 20 SEER2 averages about 600 W, and a 2-ton at 20 SEER2 about 1,200 W. Multiply by your runtime hours and divide as above.

What We See on Real Quotes

US Power designs Qcells systems from customers’ own utility data, and AC comes up in almost every conversation about sizing. The usual mistake is guessing at the AC from a generic number instead of the unit’s label and the home’s real summer bills. We ask for your last 12 months of bills and the tonnage and SEER2 from your outdoor unit, and we will tell you if replacing an old AC first makes more sense than adding panels.

Want a design based on your real usage and your real unit? Request a free, itemized estimate or call (818) 650-8010. Bring your last 12 bills and a photo of your AC’s label.

Frequently Asked Questions

How many solar panels do I need to run a 3-ton central AC?

About 4 panels (400W) cover the yearly electricity of a 3-ton, 14 SEER2 unit that runs about 900 hours a year (2,314 kWh). To run it live at midday, you need about 3.2 kW of panels, which is 9 panels at 400W or 8 at 450W. A hot climate with 1,800 runtime hours raises the yearly figure to about 8 panels.

How many solar panels do I need for a 2-ton, 4-ton, or 5-ton central AC?

At 14 SEER2, a 2-ton unit runs about 1.7 kW, a 4-ton about 3.4 kW, and a 5-ton about 4.3 kW. Covering their yearly power takes roughly 2 panels for a 2-ton in a mild climate, 11 for a 4-ton and 13 for a 5-ton in a hot climate with 1,800 runtime hours (400W panels, California-level sun). Running them live at midday takes about 6, 11, and 14 panels.

Can I run central AC on solar without a battery?

Yes, in two ways. Grid-tied panels cut your bill during sunny hours, and the grid covers the rest. A battery is only needed if you want AC to keep running after sunset on your own power. Where export credits are low, as under California’s NEM 3.0, a battery usually makes the most of your panels.

Will my solar panels run my AC during a power outage?

Not by themselves. A standard grid-tied system shuts off when the grid goes down. To run central AC in an outage, you need a battery or hybrid setup with enough power output to start the compressor, and panels sized to recharge it.

How many solar panels does it take to run AC all day?

Running a 3-ton, 14 SEER2 unit 24 hours a day would use about 62 kWh a day, or roughly 22,500 kWh a year, which takes about 38 panels at 400W in California-level sun. Real AC cycles on and off and runs far fewer hours, so no home needs this. Size for your actual runtime.

Does a higher SEER2 AC reduce the number of panels I need?

Yes. Moving from 14 to 18 SEER2 cuts the electricity used per cooling hour by about 22%. For a 3-ton unit running 900 hours a year, that takes the yearly count from 4 panels to 3.

Should I replace my AC before I go solar?

If your unit is old or failing, usually yes, or at least tell your installer the replacement is coming. Sizing solar for a unit you are about to retire can leave you with more panels than you need, and sizing for the old unit after you replace it overshoots.

About the Author

The author focuses on the integrity and energy production. Their expertise lies in optimizing residential energy footprints through the use of high-performance components, including Qcells technology and sleek, all-black solar arrays. The author serves as an energy consultant for homeowners looking to navigate the technical complexities of modern sustainable solar panels.